Welcome to Würth Sri Lanka For trade customers only

Power mounting tape

Mounting tape, Power
MNTTPE-POWER-GREY-W12MM-L10M

Art.-no. 0894909001

Prices for customers after login

Power mounting tape

Art.-no. 0894909001

Prices for customers after login

Quantity

PU

x1 pcs

Exclusively for trade customers

Register now and access more than 2,000 products

Universal double-sided, highly adhesive tape for demanding assembly bonding indoors and outdoors. Connects and seals in a single step.

Extremely high and long-lasting adhesive strength


Per running metre, holds up to:


  • 8 kg/25 mm width

  • 6 kg/19 mm width

  • 4 kg/12 mm width


Invisible connections possible


  • Optimum design without any unappealing holes, screws, rivets etc.

  • Material is not weakened by drilling, riveting etc.


2 in 1: connects and seals in a single step


  • Immediate, stress-free bonding

  • Provides vibration and shock-absorbing effect

  • Prevents rust formation


Very good moisture and UV resistance for possible use outdoors or in damp rooms.

Notice

Not recommended for use on low-energy materials such as PE or PP and hard-to-glue surfaces, e.g. PA, rubber, silicone, soft PVC, EPDM or powder-coated aluminium. Adhesion may be impaired on painted surfaces. The final adhesive force is achieved after approx. 48 hours at room temperature.



Please familiarise yourself with the applicable building regulations, which may differ from region to region, before using the adhesion solutions presented and ensure you comply with them when designing and executing your application. We recommend that you always use a mechanical safeguard for adhesive bonding above head level at 1.80 m.

The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee the consistent quality of our products. We reserve the right to make technical changes and further develop products. Please observe the technical data sheet!

Product information

Würth Catalogue(X)

Datasheets(X)

Certificates/ Documents

 | 

 | 

Application area

For adhesive bonding of an extremely broad range of materials, such as glass, untreated steel, untreated aluminium, untreated wood, concrete, ABS, hard PVC and PMMA.



Auto/cargo:


Sensors, adhesion of cover panels of all types, e.g. reflectors, mirror glass, decorative mouldings, ceilings, bumpers etc.



Metal/building services:


Bonding cable ducts, mounting signs, glass elements, grab handles, metal trim and base plates for doors and lifts, plastic parts for neon advertising.


With dome lights, conservatories etc., consider the various thermal expansion properties of the specific materials in use.



Sanitary:


Mirror, brackets, decorative elements, dispenser systems etc.



Wood/construction:


Metal profiles in façade construction, glass and plastic parts for dome lights and conservatories, window and door bars etc.

Instructions

Power assembly adhesive tapes are used to connect similar and different materials, such as uncoated metals (e.g. steel or aluminium without oxide layer), wood*, glass, high-energy plastics (ABS, polycarbonate, PMMA, hard PVC etc.)



*Caution when using with wood, its constituent compounds may influence the level of adhesive strength



It is not recommended to use on low-energy materials such as PE, PP, powder coatings, PTFE or hard-to-stick surfaces such as PA, rubber, silicone, soft PVC, EPDM etc. The maximum holding power is only achieved under optimal application conditions. The Power double-sided mounting tape holds on most smooth or lightly textured, sufficiently solid surfaces where a processing temperature of over 10°C is maintained. Lightly sanding the surface increases the surface area and can improve the adhesive strength. Any oxide layers on metals are also removed. Always remove any sanding dust before bonding. Do not use compressed air containing oil.



The resilience of the bond depends on the force applied. Best results are achieved when the entire adhesive surface is loaded (tensile and shear force), design-related line loading must be avoided (peeling force) or provided with mechanical protection. Overhead bonds are not recommended. In order to establish a bond, the tape requires sufficient contact pressure (20 N/cm²) and then sufficient time before bearing the full load. The final adhesive force is achieved after approx. 48 hours at room temperature. The bond must not be load-bearing until this time has elapsed. If used indoors, an adhesive surface of at least 25 cm² per kg of load is required; if used outdoors, at least 60 cm² per kg of load. At higher temperatures in indoor or outdoor applications, the mounting tape is softer and the retention force is thus lower.

Backing material

Acryl
Foam

Adhesive base

Acrylate

Colour

Grey

Roll width

12 mm

Length of roll

10 m

Thickness

1.10 mm

Min./max. processing temperature

15 to 30 °C

Min./max. temperature resistance

-40 to 90 °C

Max. short-term temperature resistance

150 °C

Ultraviolet resistance

Yes

Moisture resistance

Yes

Adhesive force at 25 mm

44 N

Shelf life from production/conditions

24 Month / at 10°C to 30°C

Number of rolls

1 PCS

Additional accessory:

 
Product
Description
Quantity
PU
Price
/PU
Pre-cleaner

PRECLNR-ADH-1LTR

Specially tailored cleaner for plastics, painted metal surfaces and glass parts
x 12 pcs
IPA isopropanol cleaner

UNICLNR-(IPA-CLEANER)-500ML

For universal use

Packaging unit

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

Structure of our article number

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Information on price display

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

Quantity

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.
In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Würth Catalogue

Catalogue page as PDF  | 

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information