Welcome to Würth Sri Lanka For trade customers only

Heavy-duty anchor W-TM type S with hexagon head bolt and washer

Heavy-duty anchor W-TM type S steel zinc plated
ANC-(W-TM/S-S)-(A2K)-14-M8X51

Art.-no. 0904901861
EAN 4045989060733
Prices for customers after login
Heavy-duty anchor W-TM type S with hexagon head bolt and washer

Art.-no. 0904901861

Prices for customers after login
Quantity
PU
x 50 pcs

Exclusively for trade customers

Register now and access more than 2,000 products

for uncracked concrete, zinc-plated steel

for uncracked concrete, zinc-plated steel

  • Minimal effort required to insert anchor

  • Immediate load-bearing capacity — no waiting

  • No setting tools required

  • Can be set flush with surface: Attached parts can be removed/remounted at any time

  • Triple expansion sleeve to ensure even expansion and load distribution

  • Applying the specified torque during the anchoring process ensures secure installation

  • Load-controlled/torque-controlled expanding galvanised steel anchor in sizes M6–M12

  • Cotter-pin installation
Proof of Performance

ETA-10/0255 for individual attachment, Option 7, non-cracked concrete, galvanised steel, M6–M12; dimensioned in accordance with the European Technical Approval Guidelines (ETAG) for "Metal Anchors for Use in Concrete", Appendix C, measurement process A

Notice

The partial safety factors of the resistances regulated in the approval and a partial safety factor of the effects of yF = 1.4 have been taken into account. Please refer to the European Technical Approval Guidelines (ETAG), Appendix C, for information on combining tensile and transverse loads, edge influence and groups of anchors.



The concrete has normal reinforcement. Higher values are possible for higher concrete strengths.



Compliant with approval if screws and threaded rods with acceptance test certificate 3.1 in accordance with EN 10204:2004 are proven to be the required material and to possess the mechanical properties stipulated in ETA-10/0255



If a lower mounting height is required, make a deeper drill hole accordingly

Create the drill hole

Clean the drill hole

Knock in anchor until flush

Mount component

Apply torque

ETA-10/0255 for individual attachment, Option 7, non-cracked concrete, galvanised steel, M6–M12; dimensioned in accordance with the European Technical Approval Guidelines (ETAG) for "Metal Anchors for Use in Concrete", Appendix C, measurement process A

Product information

Datasheets(X)

Certificates/ Documents

 | 

 | 

Application area

Can be used for medium to heavy loads



Suitable for attaching: Transfer lines at floor level for which flush-mounted installation is specified; steel structures, metal profiles, brackets, base plates, cable ducts, pipelines, mounting rails etc.



The anchor has European Technical Approval for use in reinforced or non-reinforced standard concrete with strength class of minimum C20/25 and maximum C50/60 in accordance with EN 206:2000-12



Can be used in concrete < C20/25, hard natural stone and solid brick masonry (without approval)



The anchor is approved for anchoring with predominantly static or quasi-static loads



Individual attachment:


Anchoring with European Technical Approval in non-cracked concrete



May only be used in dry indoor room conditions

Anchor diameter

8 mm

Anchor length (l)

51 mm

Max. attachment height (t fix)

14 mm

Nominal drill-bit diameter (d 0)

12 mm

Drill hole depth (h 1)

61 mm

Effective anchoring depth (h ef)

44.5 mm

Through-hole in the component to be connected (d f)

9 mm

Width across flats

13 mm

Material

Steel

Surface

Zinc plated

Screw length

65 mm

Performance data
Anchor diameter [mm]M6M8M10M12
Admissible centric tension load1)
on an individual anchor without influence of the edge distance type A + type S
Compressive zone
(uncracked concrete C20/252)), s ≥ 3 hef, c ≥ 1.5 hef
Nadm [kN] = C20/252)3,64,15,49,5
Admissible shear load1)
on an individual anchor without
influence of the edge distance type A + type S
Compressive zone
(uncracked concrete C20/252)), s ≥ 3 hef, c ≥ 1.5 hef
Vadm [kN] = C20/252)4,67,18,919,3
Admissible bending moment type A + type SMadm [Nm]7,017,134,259,9
Characteristic values
Minimum member thicknesshmin ≥ [mm]135135140160
Minimum spacingsmin ≥ [mm]6590135165
Minimum edge distancecmin ≥ [mm]457085115
Spacingscr,N [mm]119134155189
Edge distanceccr,N [mm]60677895
Effective anchorage depthhef [mm]39,544,551,563,0
Nominal drill diameterd0 [mm]10121418
Diameter of cutting edgesdcut ≤ [mm]10,4512,514,518,5
Drill hole depth4)h1 ≥ [mm]55617085
Through hole in the component being connecteddf ≤ [mm]791214
Torque during anchoring (type A + type S)Tinst [Nm]10254075
Torque during anchoring (type O + type H)Tinst [Nm]5122035

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information